Just How To Replace A Bathtub (For Newbies).
Just How To Replace A Bathtub (For Newbies).
Blog Article
What are your ideas about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-01-b02d6683a8ee4621bf9b9ac7ab0b1dd2.jpg)
Installing a bath tub isn't precisely rocket science, but it does call for solid plumbing, woodworking, and occasionally, tiling skills. Changing an old bathtub with a new one is additionally a moderately hard project. If the old bathtub is readily obtainable, the job can relocate rapidly; if you need to open a wall surface to remove the old tub and also position the brand-new bath tub, the task is a lot harder. In either case, the job is within a residence handyman's skills, although you will certainly need a helper to leave the old bathtub and embeded in the new one. Ensure you have actually qualified on your own for the work and fit attempting it. Instead of working with a contractor to take control of a halfway-completed task, it is far better to take into consideration employing one before you start. Chances are you may require a professional plumber to make tube links.
This write-up will assist you mount a brand-new tub in your restroom if you have actually already purchased a new tub as well as do not need to alter the plan of your previous water supply pipes.
Your tools and also product checklist must consist of the following:
Planning for the Installment
To start with, the supporting frame supplied with the bath must be fitted (if needed) according to the maker's instructions. Next, fit the taps or mixer to the tub. When fitting the tap block, it is very important to make certain that if the faucet features a plastic washing machine, it is fitted in between the bathroom and the taps. On a plastic bath, it is also sensible to fit a supporting plate under the taps unit to avoid stress on the tub.
Fit the versatile tap ports to the bottom of the two faucets using 2 nuts and olives (sometimes supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the outlet with the hole in the bath. Use the nut supplied by the manufacturer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Ensure you use all of the supplied washing machines.
Attach the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bath need to currently prepare to be fitted in its final placement.
Removing Old Taps
If you need to replace old faucets with brand-new ones as a part of your setup, then the first thing you need to do is separate the supply of water. After doing so, turn on the faucets to drain pipes any type of water remaining in the system. The procedure of getting rid of the existing taps can be fairly bothersome because of the limited gain access to that is usually the situation.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipes to the faucets. Have a cloth all set for the remaining water that will certainly originate from the pipes. As soon as the supply pipelines have actually been gotten rid of, utilize the same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary taps from transforming throughout this process. When the faucets have actually been removed, the holes in the bath/basin will certainly have to be cleaned of any type of old sealing compound.
Before going on to fit the new faucets, compare the pipeline connections on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.
Installing the Bath tub
Using both wooden boards under its feet, put the bathtub in the needed position. The wood boards are useful in evenly spreading out the weight of the bathtub over the location of the boards instead of concentrating all the weight onto four little points.
The next objective is to guarantee that the bath tub is leveled all round. This can be accomplished by examining the spirit level and readjusting the feet on the bathtub up until the level checks out degree.
To install faucets, fit all-time low of the outermost flexible faucet adapter to the suitable supply pipeline by making a compression join; then do the very same for the other faucet.
Activate the supply of water and also check all joints as well as brand-new pipework for leaks as well as tighten them if essential. Load the bathtub and likewise examine the overflow outlet as well as the regular outlet for leaks.
Finally, take care of the bathroom paneling as described in the maker's user's manual. Tiling and sealing around the tub needs to wait until the tub has actually been made use of at least once as this will resolve it right into its last placement.
Fitting New Taps
If the tails of the new faucets are plastic, after that you will certainly need a plastic connector to avoid damages to the string. One end of the adapter fits on the plastic tail of the tap and the other end supplies a link to the current supply pipes.
If you need to fit a monobloc, then you will certainly need reducing couplers, which attaches the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next off, place the faucet in the placing opening in the bath/basin ensuring that the washing machines are in place between the tap and the sink. Protect the tap in place with the maker supplied backnut. When the faucet is firmly in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with regular faucet adapters. The previous kind needs to be linked to the tap ends first, tightening just by hand. The supply pipes can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Tub
In the location where the bathroom satisfies the floor tile, it is essential to secure the joins with a silicone rubber caulking. This is essential as the installation can relocate sufficient to split an inflexible seal, creating the water to penetrate the wall surface in between the bathroom and also the tiling, bring about issues with moisture as well as possible leaks to the ceiling below.
You can select from a range of coloured sealants to blend in your fixtures and fittings. They are offered in tubes as well as cartridges, and are capable of securing spaces as much as a width of 3mm (1/8 inch). If you have a larger gap to fill, you can load it with spins of drenched newspaper or soft rope. Keep in mind to always fill the bathtub with water prior to securing, to enable the motion experienced when the tub remains in usage. The sealer can break relatively early if you do not consider this movement prior to securing.
Alternatively, ceramic coving or quadrant tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are likewise quickly available on the market. It is suggested to fit the ceramic tiles using waterproof or water resistant sticky and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I'm certainly very inquisitive about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround and I am praying you liked our entry. Be sure to set aside a second to share this article if you enjoyed reading it. We take joy in reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Show Details Report this page